With this enabled, the bot will sometimes cancel these bad queues so that it can replace them with good ones using the right hero. In this case, the bot recognizes the queue as 'bad' because it is not an optimal time to completion. Sometimes you may queue manually, or lag may cause the bot to queue with the wrong hero. If you do not have one set, the bot will attempt to use the highest attack hero available in the city. Troopdelbadque Usage:īy default, the bot will always use your traininghero to queue troops. In this case the bot will queue 500 warriors then 500 scouts then 500 pike, continuing down the line, and then restarting at the beginning of the line to rinse and repeat until the entire line goal has been met. If given the line above and using config troopincrement.01 then the bot will instead queue 1000 warriors (1%) and then queue 1000 scouts (1%), continuing down the line, and then restarting at the beginning of the line to rinse and repeat until the entire line goal has been met.įor the percentage challenged, the bot will also accept whole numbers as the actual amount to queue, eg: config troopincrement:500. The bot will first train 100k warriors, then 100k scouts, and so on without troopincrement set. By setting this goal, you can tell the bot to instead queue a percentage or specific amount of each troop on the line. will queue troops in the other you specify from left to right, on each sequential 'troop' line. Troopincrement Usage:īy default, Y.A.E.B. The bot can also use a percentage of your total population by using a number lower than '1', eg: config troopsusepopmax:0.5. You can allow it to use your entire population, by dropping production temporarily, by setting this to '1'. will only use your idle population to queue new troops. WARNING!!! Enabling this without knowing what you're doing could cause the bot to send your city into refuge! Troopsusepopmax Usage:īy default, Y.A.E.B. You can override this behavior and allow it to continue to queue new troops by enabling this goal.
The bot will not queue troops if doing so would bring it under this amount of days. will attempt keep 1 day worth of food in each city, or the number of days specified in config extrafood. Troopsusereserved Usage:īy default, Y.A.E.B. If this is not set, the bot defaults to 15 minute queue times. It is recommended to adjust this number as your traininghero's attack attribute grows or number of barracks changes, so that the bot can utilize your population and time more efficiently. This goal allows you to tell the bot how many hours per individual troop queue you want. If no switches are specified, the bot will use the configured goals for all troops, or the default settings if both are lacking. Starting with versions later than rev1268, the bot also allows switches to individual troop goal lines that will override the default and configured troop settings.
Troop /queuetime:5 /usereserved:0 /useshittyhero:1 w:100 Troop /increment.1 /queuetime.5 b:5k,t:5k If the bot is currently working on building the 4th line of troop goals, and you get attacked and you lose all your cavalry and pike, with the above settings, the bot will stop queuing the 4th line and instead build 1 pike/cav again from the 1st line, then go to the 2nd line and build the 5k pike and 1k cav, then go to the 3rd line and build the 15k pike, then resume where it left off on the 4th line. Finally, the bot will start building 400k archers, 200k scouts, 10k ballista/trans.
Once that's completed the bot will then build 250k archers, 100k scouts, 10k cav, and 5k phracts. Once that's completed the bot will then build 50k warriors, 15k pikes/swords, 50k scouts, and 200k archers. Once complete the bot will then build 100k archers, 5k ballista/trans, 15k warriors, 5k workers/pikes/swords/scouts, 1k cav/phracts, and 5 rams/pults. Using the above examples, the bot will first build 1 pike, 1 sword, and 1 cavalry in that order. The bot will not move on to the 2nd troop line until the 1st line is completed, and if at any point in time a previous line becomes invalid (eg, you get attacked and lose all your pikes) the bot will drop back to the 1st incomplete line to finish that one first. The bot reads each line from left to right, top to bottom. This directive is how you tell the bot what troops to queue for you.
0 kommentar(er)
